Conveyor Protection System

Home>Conveyor Protection System
  • BK400P Cast Aluminium Pullkey, Pull Wire Trip Type
    • BK400P Cast Aluminium Pullkey, Pull Wire Trip Type

    • BK400P Cast Aluminium Pullkey, Pull Wire Trip Type

    • Inelco International’s BK400 pullkey offers unrivaled features. As a direct replacement of the BK200 and BK300, the BK400 builds on the strengths that have witnessed sales of pullkeys since 1992. Our Pull wire type pullkey is a dual trip shaft pullkey where each trip shaft is completely independent from the other. For this pullkey it is recommended to connect the…
    • Read more
  • BK400PS Cast Aluminium Pullkey, Pull and Slack Wire Trip Type
  • BK500P Polycarbonate Pullkey, Pull Wire Trip Type
    • BK500P Polycarbonate Pullkey, Pull Wire Trip Type

    • BK500P Polycarbonate Pullkey, Pull Wire Trip Type

    • Inelco International’s BK500 pullkey offers unrivalled features. As a direct replacement of the BK200 and BK300, the BK500 builds on the strengths that have witnessed sales of pullkeys since 1992. Our Pull wire type pullkey is a dual trip shaft pullkey where each trip shaft is completely independent from the other. For this pullkey it is recommended to connect the…
    • Read more
  • BK500PS Polycarbonate Pullkey, Pull and Slack Wire Trip Type
  • BM2 Conveyor Belt Misalignment Switch
    • BM2 Conveyor Belt Misalignment Switch

    • BM2 Conveyor Belt Misalignment Switch

    • The Inelco International Conveyor Belt Misalignment Switch is designed to prevent the conveyor belt from drifting too far which could cause damage to the belt. Operation When the conveyor belt drifts during start-up, or heavy load conditions, the edge of the belt will press against the Belt alignment switch which will make or break a set of contacts that will…
    • Read more
  • BRC1 CONVEYOR BELT RIP DETECTOR
    • BRC1 CONVEYOR BELT RIP DETECTOR

    • BRC1 CONVEYOR BELT RIP DETECTOR

    • The Inelco International Conveyor Belt Rip Detection Unit is manufactured to detect belt rips on Conveyor belts. The BRC is supplied with a complete installation kit, including BRC1, 2m chain, D shackles, 2m Cable, wired to tripping Contacts. As an optional extra, our mounting brackets can be ordered for ease of installation. Downloads: BRC1-Belt-Rip-Detector.pdf
    • Read more
  • BT2000 Conveyor Belt Tear and Spillage Detector
    • BT2000 Conveyor Belt Tear and Spillage Detector

    • BT2000 Conveyor Belt Tear and Spillage Detector

    • Belt tears normally occur over the length of a conveyor and therefore it is very difficult to detect. When a belt tear oc-curred, the weight of the material normally causes the tear to open and the material will spill through the cut. The BT2000 has been designed and developed to catch the spilled material in a basket mounted below the…
    • Read more
  • RBS Return Belt Spillage and Tear Detector
    • RBS Return Belt Spillage and Tear Detector

    • RBS Return Belt Spillage and Tear Detector

    • The RBS Return Belt Spillage Detector has been designed to detect a tear that occurred in the carry belt of a conveyor belt. Material spillage through the tear on the carry belt will fall on the return belt and cause the catch plate to tilt back. A magnet attached to the catch plate is aligned with a mag-netic proximity switch.…
    • Read more
  • SGR Side Guard Removal Detector
    • SGR Side Guard Removal Detector

    • SGR Side Guard Removal Detector

    • Application Conveyor head and tail ends are normally barricaded with removable side guards to keep personnel away from dangerous areas. The Inelco International SGR-SS and SGR-DS were designed to stop the belt when a side guard has been removed. Downloads: SGR-Side-Guard-Removal-Detector.pdf
    • Read more
  • SS2000 Speed Switch with Slip Detection
  • TS 1 Conveyor Tilt Switch (Blocked Chute Detector)
    • TS 1 Conveyor Tilt Switch (Blocked Chute Detector)

    • TS 1 Conveyor Tilt Switch (Blocked Chute Detector)

    • Application Mounted hanging inside a chute at a level that the material don't normally reach during normal operation when the chute is not blocked. When a chute is blocked, material will build up from the bottom causing the tilt switch to tilt. The tilting of the switch by 35 degrees or more will cause the contacts to open and these contacts…
    • Read more

Contact Us

Products

  • Conveyor Tripping & Safety Devices
  • Conveyor Control & Monitoring Equipment
  • Earth Leakage Relays
  • Individual Electronic Protection Relays
  • Intrinically Safe Earth Continuity Relays
  • Live Line Indicators
  • Outlet Test Unit
  • Phase Rotation & Loss of Phase Relay
  • Pullkey Cables
  • Pullkey Hardware

CERTIFICATION

Copyright © Inelco International | Website & SEO done by Engineered Media

×

Cart